logo

g52.jpg

FAQ

Home > Support > Faq

Why inverter reports ‘Fan Fault’(Warning 01)

Analysis

    Maybe its related to the fan itself, or loose connection of the fan connector.

Test Method

    Open the inverter and check whether the fan is working properly or not.

Solution

    (1) If fans are working in good condition, you can upgrade 01warning firmware to clear it.

    (2) If fans are not working well, you can try to reinstall the fan connector or just try to replace the faulty fan.


Why inverter reports ‘Internal Temperature Is High’(Warning 02)

Analysis

    Something wrong with temperature sensors or something wrong with temperature sampling circuit.

Test Method

    Check 2 temperature sensors on MPPT board and mainboard. Try to swap good temperature sensors from normal inverter, and then observe if it will disappear.

Solution

    (1) You can replace 2 temperature sensors on MPPT board and mainboard.

    (2) You can also contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Is Overcharged’(Warning 03)

Analysis

    (1) Incorrect settings for lead acid battery or lithium-ion battery.

    (2) Battery voltage sample circuit may have something wrong.

Test Method

    Method 1:

    For lithium-ion battery, please confirm if lithium-ion battery can communicate with inverter. if the inverter is communicating with battery normally and it has 03warning, try to contact battery manufacturer and upgrade battery. If battery brand is not in the compatability list, please request the firmware with US2 option from Growatt. ( You can set US2 on 5th option, less than 30A for single battery on 2nd option)

    Method 2

    (1) Only connect battery to inverter( don’t connect utility, PV system and load )

    (2) Press UP an Down at the same time for 3 seconds and type 111 , then press Enter.

    (3) Select battery page , S means reduce the voltage, A means increase the voltage.

    (4) For example, LCD displays 53V and multimeter displays 50V, then type 3V on S state. And press Enter to save it.

    (5) For lead acid battery, please check 19th, 20th option on LCD. The issue may be caused by too high bulk charging voltage or floating voltage

Solution

    (1) Based on battery type, if lead acid battery, adjust 19th, 20th option. If lithium-ion battery, try to upgrade battery or inverter.

What if you have excluded above all, you may contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Voltage/Soc Is Too Low’(Warning 04)

Analysis

    04 warning means low battery. When battery voltage is lower than 44V, it will report this warning

Method

    (1) Please confirm the battery type, lead acid battery or lithium-ion battery.

    (2) Disconnect battery breaker, test the real battery voltage, and compare to battery voltage on LCD. If the voltage difference is large, try to adjust to the battery voltage based on the procedures below

Solution

    Please refer to Warning 03s solution.


Why inverter reports ‘Battery Can’t Communicate with Inverter’(Warning 20)

Analysis

Warning 20 means BMS communication error.

Method

    Replace the BMS cable, or check with Growatt whether your battery has been approved and in the compatibility list.

Solution

    If the battery was not purchased from Growatt or not in compatibility list, please try to set the battery type as US2 in the 05 setting option and let it work without BMS communication.


Why inverter reports ‘Fan Fault’(Warning 01)

Analysis

    Maybe its related to the fan itself, or loose connection of the fan connector.

Test Method

    Open the inverter and check whether the fan is working properly or not.

Solution

    (1) If fans are working in good condition, you can upgrade 01warning firmware to clear it.

    (2) If fans are not working well, you can try to reinstall the fan connector or just try to replace the faulty fan.


Why inverter reports ‘Internal Temperature Is High’(Warning 02)

Analysis

    Something wrong with temperature sensors or something wrong with temperature sampling circuit.

Test Method

    Check 2 temperature sensors on MPPT board and mainboard. Try to swap good temperature sensors from normal inverter, and then observe if it will disappear.

Solution

    (1) You can replace 2 temperature sensors on MPPT board and mainboard.

    (2) You can also contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Is Overcharged’(Warning 03)

Analysis

    (1) Incorrect settings for lead acid battery or lithium-ion battery.

    (2) Battery voltage sample circuit may have something wrong.

Test Method

    Method 1:

    For lithium-ion battery, please confirm if lithium-ion battery can communicate with inverter. if the inverter is communicating with battery normally and it has 03warning, try to contact battery manufacturer and upgrade battery. If battery brand is not in the compatability list, please request the firmware with US2 option from Growatt. ( You can set US2 on 5th option, less than 30A for single battery on 2nd option)

    Method 2

    (1) Only connect battery to inverter( don’t connect utility, PV system and load )

    (2) Press UP an Down at the same time for 3 seconds and type 111 , then press Enter.

    (3) Select battery page , S means reduce the voltage, A means increase the voltage.

    (4) For example, LCD displays 53V and multimeter displays 50V, then type 3V on S state. And press Enter to save it.

    (5) For lead acid battery, please check 19th, 20th option on LCD. The issue may be caused by too high bulk charging voltage or floating voltage

Solution

    (1) Based on battery type, if lead acid battery, adjust 19th, 20th option. If lithium-ion battery, try to upgrade battery or inverter.

What if you have excluded above all, you may contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Voltage/Soc Is Too Low’(Warning 04)

Analysis

    04 warning means low battery. When battery voltage is lower than 44V, it will report this warning

Method

    (1) Please confirm the battery type, lead acid battery or lithium-ion battery.

    (2) Disconnect battery breaker, test the real battery voltage, and compare to battery voltage on LCD. If the voltage difference is large, try to adjust to the battery voltage based on the procedures below

Solution

    Please refer to Warning 03s solution.


Why inverter reports ‘Battery Can’t Communicate with Inverter’(Warning 20)

Analysis

Warning 20 means BMS communication error.

Method

    Replace the BMS cable, or check with Growatt whether your battery has been approved and in the compatibility list.

Solution

    If the battery was not purchased from Growatt or not in compatibility list, please try to set the battery type as US2 in the 05 setting option and let it work without BMS communication.


Why inverter reports ‘Fan Fault’(Warning 01)

Analysis

    Maybe its related to the fan itself, or loose connection of the fan connector.

Test Method

    Open the inverter and check whether the fan is working properly or not.

Solution

    (1) If fans are working in good condition, you can upgrade 01warning firmware to clear it.

    (2) If fans are not working well, you can try to reinstall the fan connector or just try to replace the faulty fan.


Why inverter reports ‘Internal Temperature Is High’(Warning 02)

Analysis

    Something wrong with temperature sensors or something wrong with temperature sampling circuit.

Test Method

    Check 2 temperature sensors on MPPT board and mainboard. Try to swap good temperature sensors from normal inverter, and then observe if it will disappear.

Solution

    (1) You can replace 2 temperature sensors on MPPT board and mainboard.

    (2) You can also contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Is Overcharged’(Warning 03)

Analysis

    (1) Incorrect settings for lead acid battery or lithium-ion battery.

    (2) Battery voltage sample circuit may have something wrong.

Test Method

    Method 1:

    For lithium-ion battery, please confirm if lithium-ion battery can communicate with inverter. if the inverter is communicating with battery normally and it has 03warning, try to contact battery manufacturer and upgrade battery. If battery brand is not in the compatability list, please request the firmware with US2 option from Growatt. ( You can set US2 on 5th option, less than 30A for single battery on 2nd option)

    Method 2

    (1) Only connect battery to inverter( don’t connect utility, PV system and load )

    (2) Press UP an Down at the same time for 3 seconds and type 111 , then press Enter.

    (3) Select battery page , S means reduce the voltage, A means increase the voltage.

    (4) For example, LCD displays 53V and multimeter displays 50V, then type 3V on S state. And press Enter to save it.

    (5) For lead acid battery, please check 19th, 20th option on LCD. The issue may be caused by too high bulk charging voltage or floating voltage

Solution

    (1) Based on battery type, if lead acid battery, adjust 19th, 20th option. If lithium-ion battery, try to upgrade battery or inverter.

What if you have excluded above all, you may contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Voltage/Soc Is Too Low’(Warning 04)

Analysis

    04 warning means low battery. When battery voltage is lower than 44V, it will report this warning

Method

    (1) Please confirm the battery type, lead acid battery or lithium-ion battery.

    (2) Disconnect battery breaker, test the real battery voltage, and compare to battery voltage on LCD. If the voltage difference is large, try to adjust to the battery voltage based on the procedures below

Solution

    Please refer to Warning 03s solution.


Why inverter reports ‘Battery Can’t Communicate with Inverter’(Warning 20)

Analysis

Warning 20 means BMS communication error.

Method

    Replace the BMS cable, or check with Growatt whether your battery has been approved and in the compatibility list.

Solution

    If the battery was not purchased from Growatt or not in compatibility list, please try to set the battery type as US2 in the 05 setting option and let it work without BMS communication.


Why inverter reports ‘Fan Fault’(Warning 01)

Analysis

    Maybe its related to the fan itself, or loose connection of the fan connector.

Test Method

    Open the inverter and check whether the fan is working properly or not.

Solution

    (1) If fans are working in good condition, you can upgrade 01warning firmware to clear it.

    (2) If fans are not working well, you can try to reinstall the fan connector or just try to replace the faulty fan.


Why inverter reports ‘Internal Temperature Is High’(Warning 02)

Analysis

    Something wrong with temperature sensors or something wrong with temperature sampling circuit.

Test Method

    Check 2 temperature sensors on MPPT board and mainboard. Try to swap good temperature sensors from normal inverter, and then observe if it will disappear.

Solution

    (1) You can replace 2 temperature sensors on MPPT board and mainboard.

    (2) You can also contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Is Overcharged’(Warning 03)

Analysis

    (1) Incorrect settings for lead acid battery or lithium-ion battery.

    (2) Battery voltage sample circuit may have something wrong.

Test Method

    Method 1:

    For lithium-ion battery, please confirm if lithium-ion battery can communicate with inverter. if the inverter is communicating with battery normally and it has 03warning, try to contact battery manufacturer and upgrade battery. If battery brand is not in the compatability list, please request the firmware with US2 option from Growatt. ( You can set US2 on 5th option, less than 30A for single battery on 2nd option)

    Method 2

    (1) Only connect battery to inverter( don’t connect utility, PV system and load )

    (2) Press UP an Down at the same time for 3 seconds and type 111 , then press Enter.

    (3) Select battery page , S means reduce the voltage, A means increase the voltage.

    (4) For example, LCD displays 53V and multimeter displays 50V, then type 3V on S state. And press Enter to save it.

    (5) For lead acid battery, please check 19th, 20th option on LCD. The issue may be caused by too high bulk charging voltage or floating voltage

Solution

    (1) Based on battery type, if lead acid battery, adjust 19th, 20th option. If lithium-ion battery, try to upgrade battery or inverter.

What if you have excluded above all, you may contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Voltage/Soc Is Too Low’(Warning 04)

Analysis

    04 warning means low battery. When battery voltage is lower than 44V, it will report this warning

Method

    (1) Please confirm the battery type, lead acid battery or lithium-ion battery.

    (2) Disconnect battery breaker, test the real battery voltage, and compare to battery voltage on LCD. If the voltage difference is large, try to adjust to the battery voltage based on the procedures below

Solution

    Please refer to Warning 03s solution.


Why inverter reports ‘Battery Can’t Communicate with Inverter’(Warning 20)

Analysis

Warning 20 means BMS communication error.

Method

    Replace the BMS cable, or check with Growatt whether your battery has been approved and in the compatibility list.

Solution

    If the battery was not purchased from Growatt or not in compatibility list, please try to set the battery type as US2 in the 05 setting option and let it work without BMS communication.


Why inverter reports ‘Fan Fault’(Warning 01)

Analysis

    Maybe its related to the fan itself, or loose connection of the fan connector.

Test Method

    Open the inverter and check whether the fan is working properly or not.

Solution

    (1) If fans are working in good condition, you can upgrade 01warning firmware to clear it.

    (2) If fans are not working well, you can try to reinstall the fan connector or just try to replace the faulty fan.


Why inverter reports ‘Internal Temperature Is High’(Warning 02)

Analysis

    Something wrong with temperature sensors or something wrong with temperature sampling circuit.

Test Method

    Check 2 temperature sensors on MPPT board and mainboard. Try to swap good temperature sensors from normal inverter, and then observe if it will disappear.

Solution

    (1) You can replace 2 temperature sensors on MPPT board and mainboard.

    (2) You can also contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Is Overcharged’(Warning 03)

Analysis

    (1) Incorrect settings for lead acid battery or lithium-ion battery.

    (2) Battery voltage sample circuit may have something wrong.

Test Method

    Method 1:

    For lithium-ion battery, please confirm if lithium-ion battery can communicate with inverter. if the inverter is communicating with battery normally and it has 03warning, try to contact battery manufacturer and upgrade battery. If battery brand is not in the compatability list, please request the firmware with US2 option from Growatt. ( You can set US2 on 5th option, less than 30A for single battery on 2nd option)

    Method 2

    (1) Only connect battery to inverter( don’t connect utility, PV system and load )

    (2) Press UP an Down at the same time for 3 seconds and type 111 , then press Enter.

    (3) Select battery page , S means reduce the voltage, A means increase the voltage.

    (4) For example, LCD displays 53V and multimeter displays 50V, then type 3V on S state. And press Enter to save it.

    (5) For lead acid battery, please check 19th, 20th option on LCD. The issue may be caused by too high bulk charging voltage or floating voltage

Solution

    (1) Based on battery type, if lead acid battery, adjust 19th, 20th option. If lithium-ion battery, try to upgrade battery or inverter.

What if you have excluded above all, you may contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Voltage/Soc Is Too Low’(Warning 04)

Analysis

    04 warning means low battery. When battery voltage is lower than 44V, it will report this warning

Method

    (1) Please confirm the battery type, lead acid battery or lithium-ion battery.

    (2) Disconnect battery breaker, test the real battery voltage, and compare to battery voltage on LCD. If the voltage difference is large, try to adjust to the battery voltage based on the procedures below

Solution

    Please refer to Warning 03s solution.


Why inverter reports ‘Battery Can’t Communicate with Inverter’(Warning 20)

Analysis

Warning 20 means BMS communication error.

Method

    Replace the BMS cable, or check with Growatt whether your battery has been approved and in the compatibility list.

Solution

    If the battery was not purchased from Growatt or not in compatibility list, please try to set the battery type as US2 in the 05 setting option and let it work without BMS communication.


Why inverter reports ‘Fan Fault’(Warning 01)

Analysis

    Maybe its related to the fan itself, or loose connection of the fan connector.

Test Method

    Open the inverter and check whether the fan is working properly or not.

Solution

    (1) If fans are working in good condition, you can upgrade 01warning firmware to clear it.

    (2) If fans are not working well, you can try to reinstall the fan connector or just try to replace the faulty fan.


Why inverter reports ‘Internal Temperature Is High’(Warning 02)

Analysis

    Something wrong with temperature sensors or something wrong with temperature sampling circuit.

Test Method

    Check 2 temperature sensors on MPPT board and mainboard. Try to swap good temperature sensors from normal inverter, and then observe if it will disappear.

Solution

    (1) You can replace 2 temperature sensors on MPPT board and mainboard.

    (2) You can also contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Is Overcharged’(Warning 03)

Analysis

    (1) Incorrect settings for lead acid battery or lithium-ion battery.

    (2) Battery voltage sample circuit may have something wrong.

Test Method

    Method 1:

    For lithium-ion battery, please confirm if lithium-ion battery can communicate with inverter. if the inverter is communicating with battery normally and it has 03warning, try to contact battery manufacturer and upgrade battery. If battery brand is not in the compatability list, please request the firmware with US2 option from Growatt. ( You can set US2 on 5th option, less than 30A for single battery on 2nd option)

    Method 2

    (1) Only connect battery to inverter( don’t connect utility, PV system and load )

    (2) Press UP an Down at the same time for 3 seconds and type 111 , then press Enter.

    (3) Select battery page , S means reduce the voltage, A means increase the voltage.

    (4) For example, LCD displays 53V and multimeter displays 50V, then type 3V on S state. And press Enter to save it.

    (5) For lead acid battery, please check 19th, 20th option on LCD. The issue may be caused by too high bulk charging voltage or floating voltage

Solution

    (1) Based on battery type, if lead acid battery, adjust 19th, 20th option. If lithium-ion battery, try to upgrade battery or inverter.

What if you have excluded above all, you may contact Growatt Service Team for further solutions.


Why inverter reports ‘Battery Voltage/Soc Is Too Low’(Warning 04)

Analysis

    04 warning means low battery. When battery voltage is lower than 44V, it will report this warning

Method

    (1) Please confirm the battery type, lead acid battery or lithium-ion battery.

    (2) Disconnect battery breaker, test the real battery voltage, and compare to battery voltage on LCD. If the voltage difference is large, try to adjust to the battery voltage based on the procedures below

Solution

    Please refer to Warning 03s solution.


Why inverter reports ‘Battery Can’t Communicate with Inverter’(Warning 20)

Analysis

Warning 20 means BMS communication error.

Method

    Replace the BMS cable, or check with Growatt whether your battery has been approved and in the compatibility list.

Solution

    If the battery was not purchased from Growatt or not in compatibility list, please try to set the battery type as US2 in the 05 setting option and let it work without BMS communication.


1

2

Jump to
Subscribe to our newsletter

Subscribe Now!

Subscribe

Subscribe to the Growatt Newsletter

Insert your details below to receive information

*Enter Verification Code:

code
follow us

© Growatt New Energy All Rights Reserved